Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -38,31 +38,14 @@
38	38	Version 3a introduces the following main changes:
39	39
40	40	* Substantially increased granularity of products and processes for audit and certification scope.
41		-
42		-=== Quality Management System Requirements ===
43		-
44		-* //#0654#: Design and Development – Product Qualification Report// — Lack of qualification data, and major NC without CSI letter now prohibit CQM certification
45		-* IQC (Incoming Quality Control) to be assessed during CQM Audits for each CQM product and component, and not just once as part of the QMS
46		-* //#0703# Release of Product and Services, Batch Yield Limit// — split into two independent requirements: //#0703#: Production and Service Provision – Release of Product and Services// and //#0707#: Production and Service Provision – Batch Yield Limit//; Batch Yield Limit now only applicable to products containing an IC.
47		-* Requirements to implement SPC (//#0705#: Performance evaluation – Statistical Process Control//) and CpK (//#0811#: Performance evaluation – Process Capability//) restricted to ic icm iacicm bsm il iacil iac, that is, where processes involve wafer processing or IC packaging processes.
48		-
49		-=== Product Requirements ===
50		-
51		-* #3046#: Resistance to Chemicals — For CQM products and components where// #3058#: Solidity – Adhesion of ICM to Card// is required, clarified that one sample per solution shall be tested for //#3058#: Solidity – Adhesion of ICM to Card//
52		-* //#3050#: ESD Conductivity – ESC — //Increased permitted levels of ESD conductivity
53		-* //#3067#: Suitability for an Identification Notch — //Permitting greater tolerances
54		-* //#3110#: IAC – Interactive Cards – Requirement to maintain a valid CSI Letter// — restricted to specific products, clarified to which products and components this requirement still applies.
55		-* //#3120#: Pilot, innovative, and interactive cardholder identification products// – //requirement to undergo CQM Audits depending on annual production volume// — New requirement easing CQM audit and CQM certification requirements for innovative and interactive cardholder products with very small volumes.
56		-* //#3130#: Products that are not compliant with applicable CQM requirements – Requirement to maintain a valid CSI Letter// — Now an individual requirement to clarify better that CQM non conformities must be covered by a CSI letter.
57		-* //#3057#: 3 wheel Test Robustness for Interactive Cards (“IAC”) and ICC made without an ICM// — added clarification regarding re-using samples and regarding interpretation of test results with higher force than required.
58		-* //#2041#: Fingerprint Sensor – Resistance to Abrasion// — Reworded to improve understanding.
59		-* //#3058#: Solidity – Adhesion of ICM to Card// — Separate minimum value defined for rupture of the ICM, provided the ICM remains attached in all corners of the ICC.
60		-* //#2805#: Antenna Design – Minimum distance between mechanical personalization areas and the antenna in IL, ICC, IAC// — Wording revised to better accommodate IAC.
61		-
62		-=== Test methods ===
63		-
64		-* //#7010#: Pantone-Colours//  — specified measurement parameters for colour measurement using spectrometer
65		-* //#7120#: Security Devices (Hologram, PBM, magnetic stripe with hologram like surface, Signature Panel) – Adhesion, Aspect and Shape, Size and Positioning// — clarified that if cross-hatch necessary, a new sample shall be used
66		-* //#8093#: Temperature Cycling// — extended maximum period between removal from oven and verification of functionality to 72 h to accommodate weekends
67		-* #8230#: //Solidity – ICM Adhesion – Back of Card Spot Pressure Test// — Clarifed positioning of centre of pressure for multicentric ICM, for example combining ISO/IEC 7816-2 contacts and a fingerprint sensor into a single ICM
68		-* //#8310#: Resistance of a Fingerprint Sensor against Scratching// — Additional details specified
	41	+* Lack of qualification data, and major NC without CSI letter prohibit CQM certification (#0654#)
	42	+* IQC (Incoming Quality Control) to be assessed for each product, and not just once as part of the QMS
	43	+* Separation of #0703# Release of Product and Services, Batch Yield Limit, into two independent requirements #0703# and #0707#, Batch Yield Limit now only applicable to products containing an IC.
	44	+* Requirement to implement SPC and CpK restricted to ic icm iacicm bsm il iacil iac, so processes involving wafer processing or IC packaging processes.
	45	+* For cards, when testing Resistance to Checmicals, clarified that where// #3058#: Solidity – Adhesion of ICM to Card// is required, one sample per solution shall be tested for //#3058#: Solidity – Adhesion of ICM to Card//
	46	+* Increased permitted levels of ESD conductivity for //#3050#: ESD Conductivity - ESC//
	47	+* Permitting greater tolerances in //#3067#: Suitability for an Identification Notch//
	48	+* //#3110#: IAC – Interactive Cards – Requirement to maintain a valid CSI Letter// restricted to specific products, clarified to which products and components this requirement still applies.
	49	+* Added //#3120#: Pilot, innovative, and interactive cardholder identification products requirement to undergo CQM Audits depending on annual production volume//, easing CQM audit and CQM certification requirements for innovative and interactive cardholder products with very small volumes.
	50	+* Made //#3130#: Products that are not compliant with applicable CQM requirements – Requirement to maintain a valid CSI Letter// individual requirement to clarify that CQM non conformities must be covered by a CSI letter.
	51	+*