Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -43,21 +43,20 @@
43	43
44	44	* //#0654#: Design and Development – Product Qualification Report// — Lack of qualification data, and major NC without CSI letter now prohibit CQM certification
45	45	* IQC (Incoming Quality Control) to be assessed during CQM Audits for each CQM product and component, and not just once as part of the QMS
46		-* //#0662#: Requirements for Products and Services – Determining the Requirements for Products and Services, Order Specification// — Order Specification appended to title to clarify that an Order Specification is required, verbiage added to clarify Order Specification
47	47	* //#0703# Release of Product and Services, Batch Yield Limit// — split into two independent requirements: //#0703#: Production and Service Provision – Release of Product and Services// and //#0707#: Production and Service Provision – Batch Yield Limit//; Batch Yield Limit now only applicable to products containing an IC.
48	48	* Requirements to implement SPC (//#0705#: Performance evaluation – Statistical Process Control//) and CpK (//#0811#: Performance evaluation – Process Capability//) restricted to ic icm iacicm bsm il iacil iac, that is, where processes involve wafer processing or IC packaging processes.
49	49
50	50	=== Product Requirements ===
51	51
52		-* #3046#: Resistance to Chemicals — For CQM products and components where// #3058#: Solidity – Adhesion of ICM to Card// is required, clarified that one sample per solution shall be tested for //#3058#: Solidity – Adhesion of ICM to Card//
53		-* //#3050#: ESD Conductivity – ESC — //Increased permitted levels of ESD conductivity
54		-* //#3067#: Suitability for an Identification Notch — //Permitting greater tolerances
55		-* //#3110#: IAC – Interactive Cards – Requirement to maintain a valid CSI Letter// — restricted to specific products, clarified to which products and components this requirement still applies.
56		-* //#3120#: Pilot, innovative, and interactive cardholder identification products// – //requirement to undergo CQM Audits depending on annual production volume// — New requirement easing CQM audit and CQM certification requirements for innovative and interactive cardholder products with very small volumes.
57		-* //#3130#: Products that are not compliant with applicable CQM requirements – Requirement to maintain a valid CSI Letter// — Now an individual requirement to clarify better that CQM non conformities must be covered by a CSI letter.
	51	+* For cards, when testing Resistance to Chemicals, clarified that where// #3058#: Solidity – Adhesion of ICM to Card// is required, one sample per solution shall be tested for //#3058#: Solidity – Adhesion of ICM to Card//
	52	+* Increased permitted levels of ESD conductivity for //#3050#: ESD Conductivity — ESC//
	53	+* Permitting greater tolerances in //#3067#: Suitability for an Identification Notch//
	54	+* //#3110#: IAC – Interactive Cards – Requirement to maintain a valid CSI Letter// restricted to specific products, clarified to which products and components this requirement still applies.
	55	+* Added //#3120#: Pilot, innovative, and interactive cardholder identification products requirement to undergo CQM Audits depending on annual production volume//, easing CQM audit and CQM certification requirements for innovative and interactive cardholder products with very small volumes.
	56	+* Made //#3130#: Products that are not compliant with applicable CQM requirements – Requirement to maintain a valid CSI Letter// individual requirement to clarify that CQM non conformities must be covered by a CSI letter.
58	58	* //#3057#: 3 wheel Test Robustness for Interactive Cards (“IAC”) and ICC made without an ICM// — added clarification regarding re-using samples and regarding interpretation of test results with higher force than required.
59	59	* //#2041#: Fingerprint Sensor – Resistance to Abrasion// — Reworded to improve understanding.
60		-* //#3058#: Solidity – Adhesion of ICM to Card// — Separate minimum value defined for rupture of the ICM, provided the ICM remains attached in all corners of the ICC.
	59	+* //#3058#: Solidity – Adhesion of ICM to Card// — TBD
61	61	* //#2805#: Antenna Design – Minimum distance between mechanical personalization areas and the antenna in IL, ICC, IAC// — Wording revised to better accommodate IAC.
62	62
63	63	=== Test methods ===
...	...	@@ -64,6 +64,4 @@
64	64
65	65	* //#7010#: Pantone-Colours//  — specified measurement parameters for colour measurement using spectrometer
66	66	* //#7120#: Security Devices (Hologram, PBM, magnetic stripe with hologram like surface, Signature Panel) – Adhesion, Aspect and Shape, Size and Positioning// — clarified that if cross-hatch necessary, a new sample shall be used
67		-* //#8093#: Temperature Cycling// — extended maximum period between removal from oven and verification of functionality to 72 h to accommodate weekends
68		-* #8230#: //Solidity – ICM Adhesion – Back of Card Spot Pressure Test// — Clarified positioning of centre of pressure for multicentric ICM, for example combining ISO/IEC 7816-2 contacts and a fingerprint sensor into a single ICM
69	69	* //#8310#: Resistance of a Fingerprint Sensor against Scratching// — Additional details specified